FAQS

Plastic Design Guide

PLASTIC DESIGN GUIDE

CNM engineers and designers can work with you to develop and design your plastic injection molded component. To ensure a quality part, there are three major areas of focus throughout the design stage:

  1. Proper plastic part design
  2. Proper material selection plastic part design
  3. Processing conditions for plastic injection molding

The designers and engineers at CNM have over 250 combined years of experience in designing parts for plastic injection molding, selecting materials, and processing resins (specializing in engineering and high performance resins). This guide was designed to demonstrate the basic elements of proper plastic part design.

DESIGNING PARTS FOR UP & DOWN MOLDING HELPS CONTROL COST

Designing a part that can be molded with a "straight pull" or "up & down" motion is a great way to keep the cost of the mold down. A straight pull mold is designed so that when the two halves (A side and B side) of the mold separate from each other, there is no plastic blocking the path of the metal in the direction of the pull. Undercuts on the part cause this blockage of path and require an action in the mold (cams, core pulls, etc.). Action in the mold can have a major impact on the cost (and overall size) of a mold.

UNIFORM WALL THICKNESS HELPS TO PREVENT DEFECTS

Proper wall thickness is one of the most fundamental requirements in designing a part for plastic injection molding. Plastic shrinks as it cools which can lead to defects such as sink marks, voids, stresses, and warping. Plastic resin solidifies in the mold nearer to the outside of the part (closest to the mold surface). Thick sections of a part tend to pull inward, creating stresses, sink marks, or voids. Since thinner sections cool quicker, stress can build in the part between thinner and thicker sections, resulting in part warpage.

DRAFT ALLOWS FOR PARTS TO RELEASE FROM THE MOLD

Draft is required on all parts in the direction of mold movement in order to allow parts to release or eject from the mold properly. Draft is the angle in which the part is tapered to allow it to release. As the part cools, it tends to want to shrink to the core side of the mold. Adding draft helps the part to release. Most parts or applications require a minimum of 1/2 to 1 degree, however 11/2 to 2 degrees is widely accepted as the norm.


HOLES ENHANCE PART FUNCTIONALITY AND REDUCE WEIGHT

Holes can be added to a part for functionality or to reduce overall part weight (coring). Core pins are typically used to form a hole, preventing the molten plastic from filling in that space. Through holes go all the way through a part. Blind holes do not completely go through a part. Core pins for a blind hole are only supported by one end, so there is a greater degree of difficulty in forming them without defect. Forming holes can lead to defects or have a negative impact on aesthetics. Since the molten plastic flows around the core pin, it can leave a weld line (which may be visible and/or be weaker than the remainder of the part).

  1. The depth of a blind hole should be about two times the diameter of the core pin for small pins (less than 3/16") and four times the diameter of the core pin for pins greater than 3/16".
  2. Distance from the edge of a hole to a vertical surface (edge or part or rib) or another hole should be at least two times the thickness of the part or at least the diameter of the core pin (hole).
  3. Holes created in the direction of the opening/closing of the mold or parallel to the parting line are relatively easy to produce. Holes at different angles can be created, but may require special action in the mold utilizing core pulls or cams which can have significant cost impacts.

BOSSES AID IN ASSEMBLY AND MOUNTING

Bosses can be added to the part design for assembly, locating, or mounting of a part. Improper placement of a boss leads to uneven wall thickness and can have a negative impact on the aesthetics, shrinking, or strength of a part.

  1. Wall thickness around a boss feature should be 55%–65% of the nominal wall thickness for thin walls (less than 1/8") or around 40% of the nominal wall thickness if greater than 1/8"
  2. Boss height should be no more than 2 1/2 times the diameter of a hole in the boss

RIBS ENHANCE PART STRENGTH AND STABILITY

Ribs can be added to parts to add rigidity or stiffness. Adding ribs allows for a part to increase strength and bear a higher load. Ribs too have recommended guidelines to maximize functionality and minimize defects.

  1. Rib thickness should be less than the wall thickness. Recommended thickness is 60% to 80% of the nominal wall.
  2. Adding more ribs adds more strength or stiffness to a part. It is better to add more ribs than make larger or thicker ribs.
  3. Ribs should be spaced at least two times the nominal wall thickness from one another.
  4. Rib height should be less than three times the nominal wall thickness of the part.
  5. If a thick rib is required, the center of the rib should be cored (cut out) to allow for uniform wall thickness.

ADDING A RADIUS REDUCES STRESS ON CORNERS

Radii should be added to angles to prevent sharp corners. Corners can lead to stresses, limit material flow, and often reduce part strength.

  1. Inside radius of a corner should be at least half of the wall thickness
  2. Outside radius of a corner should be equal to the part thickness plus the inside radius
  3. A radius being added to a boss or rib should be 1/4 of the part thickness, no smaller than .015

Material selection and processing conditions are equally important factors in the proper design for a plastic injection molded component or part.

We understand that initially, material selection may seem overwhelming since there are so many materials to choose from. You can rest easy knowing that CNM has partnered with resin suppliers for over 60 years and has a multitude of experience in manufacturing plastic parts with even the most difficult-to-process resins. Please see our basic resin guide for a few examples of commodity and engineering resins that CNM has become an expert in molding.

栏目导航

    联系我们

    CONTACT US

    联系人:Cairne Lu

    手机:+86 186 0305 5216

    电话:+86 755 2841 9935

    邮箱:info\'\'at\'\'chinaunitedmould.com

    地址: 2nd Floor, No.49 Jinkang Rd, Pingshan District, Shenzhen